Tags: Keyestudio, Maker, Learning, Kit, ARDUINO, BOARD, Uno, LCD, Hello World, LED blinking, PWM, Traffic light, LED chasing effect, Button-controlled LED, Active buzzer, Passive buzzer, RGB LED, Photo resistor, Flame sensor, LM35 temperature sensor, Tilt switch, IR remote control, Analog value reading, 74HC595, 1-digit LED segment display, 8*8 LED matrix, 1602 LCD, 9g servo control, 5V Stepper Motor, PIR Motion Sensor, Analog Gas Sensor, ADXL345 Three Axis Acceleration Module, HC-SR04 Ultrasonic Sensor, Joystick Module, 5V Relay Module

Keyestudio New sensor kit 37 in 1 box for Arduino

  • 185.00 AED
    • Ex Tax:185.00 AED
    • Reward Points: %s 1
    • Brands Keyestudio
    • Product Code: Keyestudio
    • Availability: In Stock
    This is keyestudio sensor learning kit. We bring together 37 basic sensors and modules, aiming for the convenient learning for starters. Inside this box, there are digital and analog sensors and also some special modules such as ultrasonic, Bluetooth, acceleration module,etc.For each module, there i..

    This is keyestudio sensor learning kit. We bring together 37 basic sensors and modules, aiming for the convenient learning for starters. Inside this box, there are digital and analog sensors and also some special modules such as ultrasonic, Bluetooth, acceleration module,etc.
    For each module, there is clear connection diagram and sample code. So even if you are totally new at this, you can get started easily.The sample codes for this sensor kit are based on ARDUINO because it's open source and easy to use. If you are good at this, you can also apply this kit to other MCU development platforms, such as 51, STM32, Raspberries Pi. The working principle is pretty much the same.
    Now, let us embrace this fascinating world of ARDUINO and learn together!
    thumb

    Project Details


    Project 1: White LED Light


    Introduction
    This is a white LED module. The main function is to control a plugin LED on and off. When connecting to ARDUINO, after programming, it will emit white light color.
    The pin pitch of 3Pin is 2.54mm. This LED module has 3 Pins; - pin is connected to ground, + pin is connected to VCC(3.3-5V), S pin is for signal control; you can set the High or Low level to control the LED on and off.
    You can combine with other sensors to do various interactive experiments. You can also choose other LED modules to emit different light color like blue, green, yellow and red.

    thumb


    Features

    • Control interface: Digital
    • Working voltage: DC 3.3-5V
    • Pin pitch: 2.54mm
    • LED color: white
    • Easy to use
    • Useful for light projects


    Connect It Up
    Connect the LED module to control board using three jumper wires. Then connect the control board to your PC with a USB cable.

    thumb


    Upload the Code
    Copy and paste below code to Arduino IDE and upload.

    int led = 7; 
    void setup()
    {
      pinMode(led, OUTPUT);     //Set Pin7 as output
    }
    void loop()
    {    digitalWrite(led, HIGH);   //Turn off led
              delay(1000);
              digitalWrite(led, LOW);    //Turn on led
              delay(1000);
    }
    


    Test Result
    The LED will flash on for one second, then off for one second, repeatedly and alternately.
    If it doesn’t, make sure you have assembled the circuit correctly and verified and uploaded the code to your board.

    thumb


    Project 2: Red LED Light


    Introduction
    This is a red LED module. The main function is to control a plugin LED on and off. When connecting to ARDUINO, after programming, it will emit red light color.
    The pin pitch of 3Pin is 2.54mm. This LED module has 3 Pins; - pin is connected to ground, + pin is connected to VCC(3.3-5V), S pin is for signal control; you can set the High or Low level to control the LED on and off.
    You can combine with other sensors to do various interactive experiments.
    You can also choose other LED modules to emit different light color like blue, green, yellow and white.

    thumb


    Features

    • Control interface: Digital
    • Working voltage: DC 3.3-5V
    • Pin pitch: 2.54mm
    • LED color: red
    • Easy to use
    • Useful for light projects


    Technical Details

    • Dimensions: 34mm*20mm*11.5mm
    • Weight: 2.7g


    Connect It Up
    Connect the red LED module to control board using three jumper wires. Then connect the control board to your PC with a USB cable.

    thumb


    Upload the Code
    Copy and paste below code to Arduino IDE and upload.

    int led = 7; 
    void setup()
    {
      pinMode(led, OUTPUT);     //Set Pin7 as output
    }
    void loop()
    {    digitalWrite(led, HIGH);   //Turn off led
              delay(1000);
              digitalWrite(led, LOW);    //Turn on led
              delay(1000);
    }
    


    Test Result
    The LED will flash on for one second, then off for one second, repeatedly and alternately.
    If it doesn’t, make sure you have assembled the circuit correctly and verified and uploaded the code to your board.

    thumb


    Project 3: 3W LED Module


    Introduction
    This LED module is of high brightness because the lamp beads it carries is 3W. We can apply this module to Arduino projects.
    For example, intelligent robots can use this module for illumination purpose.
    Please note that the LED light can't be exposed directly to human eyes for safety concerns.
    thumb


    Specification

    • Color temperature: 6000~7000K
    • Luminous flux: 180~210lm
    • Current: 700~750mA
    • IO Type: Digital
    • Supply Voltage: 3.3V to 5V
    • Power: 3W
    • Light angle: 140 degree
    • Working temperature: -50~80℃
    • Storage temperature: -50~100℃
    • High power LED module, controlled by IO port microcontroller
    • Great for Robot and search & rescue platform application


    Connection Diagram
    thumb


    Sample Code

    // the setup function runs once when you press reset or power the board
    void setup() {
      // initialize digital pin 13 as an output.
      pinMode(13, OUTPUT);
    }
    
    // the loop function runs over and over again forever
    void loop() {
      digitalWrite(13, HIGH);   // turn the LED on (HIGH is the voltage level)
      delay(1000);              // wait for a second
      digitalWrite(13, LOW);    // turn the LED off by making the voltage LOW
      delay(1000);              // wait for a second
    }
    


    Result
    Done wiring and powered up,upload well the code, both D13 led and the led on the module blink for one second then off, circularly.


    FOR MORE INFO: LINK

    There are no reviews for this product.

    Write a review

    Please login or register to review