Tags: , Bluetooth, 4.0, AT-05, BLE, Module, compatible, HM-10

Bluetooth 4.0 AT-05 BLE Module compatible HM-10

  • 15.00 AED
    • Ex Tax:15.00 AED
    • Product Code: BLE
    • Availability: In Stock
    If you are in need of such a 4.0 BLE Bluetooth module, MCU can be set up,also can controlled by a remote Bluetooth device for setting,can transfer data, and can remotely control 10 PIO pins,so,the best choice is HM-10 or Bluetooth 4.0 AT-05 BLE Module compatible HM-10 bluetooth module. can..

    If you are in need of such a 4.0 BLE Bluetooth module, MCU can be set up,also can controlled by a remote Bluetooth device for setting,can transfer data, and can remotely control 10 PIO pins,so,the best choice is HM-10 or Bluetooth 4.0 AT-05 BLE Module compatible HM-10 bluetooth module. can replace HC-05, HC-06, HC-07 etc.

    Support Central and Peripheral mode switch, modify by AT commander.

    Support Remote control mode, remote device can control PIO pin or modify settings by AT commander when Connected. (such as Iphone4s/5 ipad, Note2 etc.)

    The Bluetooth UART RS232 serial Converter Module can easily transfer the UART data through the wireless Bluetooth, without complex PCB layout or deep knowledge in the Bluetooth software stack, you can combine this bluetooth module with your system:

    • MCU, ARM or DSP systems. SOC systems. And Others

    4.0 BLE bluetooth to uart transceiver Module Central Peripheral HM-10 CC2540

    support Central and Peripheral mode switch, modify by AT commander

    Support Remote control mode, remote device can control PIO pin or modify settings by AT commander when Connected. (such as Iphone4s/5 ipad, Note2 etc.)

    Specifications:

    • Pin description

      UART_TX--Serial data output

      UART_RX--Serial data input

      VCC--Power supply 3.3V

      GND--ground

      P1_3--Disconnect pin (200ms ground pulse disconnected)

      P1_2--LED and other pins (not connected flashing, online long bright)

      P1_1--Bluetooth connection port

      RESETB--low level reset, at least 5ms

      SDA--data port


      Bluetooth protocol: 4.0

      Operating frequency: 2.4GHz ISM band

      Communication interface: UART

      Power supply: 3.3V

      Antenna: PCB onboard antenna (external DB antenna)

      Communication distance: 30-40M (open environment)

      Bluetooth certification: BQB FCC CE ROHS REAch

      Bluetooth name: BT05

      Serial port parameters: 9800, 8-bit data, 1 stop bit, no parity, no flow control

      Air upgrade: support OTA air upgrade

      Maximum single packet bytes: 280 Bytes

      Service UUID: FFE0

      Notify UUID: FFE1

      Write UUID: FFE2

      Storage temperature: MIN: -55 °C-MAX: +125 °C

      Work temperature: MIN: -20 °C-MAX: +70 °C

    • Size:26.9mm x 13mm x 2.2 mm
    • Flash:256Kb

     DataSheet


    Additional introduction:

     

    HM-10 is Bluetooth V4.0 BLE version. Use TI chip. HM Bluetooth module use CSR BlueCore or TI CC2540, Master and slave roles

    in one, transmission version and remote control version and PIO state acquisition functions in one, Support the AT command modify

    module parameters, Convenient and flexible. Transmission version can be used to transmit data between two Bluetooth devices.Remote

    Control version can be used to Control PIO ports output high or low level without any other MCU.

    AT Commanders (new version V542)

    AT (Test command)

    AT+BAUD (Query/Set Baud rate)

    AT+chK (Query/Set parity)

    AT+STOP (Query/Set stop bit)

    AT+UART (Query/Set uart rate,parity, stop bit)

    AT+PIO (Query/Set PIO pins status Long command)

    AT+PIO (Query/Set a PIO pin sttus Short command)

    AT+NAME (Query/Set device friendly name)

    AT+PIN (Query/Set device password code)

    AT+DEFAULT (Reset device settings)

    AT+RESTART (Restart device)

    AT+ROLE (Query/Set device mode, Master or Slave)

    AT+CLEAR (Clear remote device address if has)

    AT+CONLAST (Try to connect last connect succeed device)

    AT+VERSION (Show software version information)

    AT+HELP (Show help information)

    AT+RADD (Query remote device address)

    AT+LADD (Query self address)

    AT+IMME (Query/Set Whether the device boot immediately)

    AT+WORK (if device not working, start work, use with AT+IMME command)

    AT+TCON (Query/Set Try to connect remote times)

    AT+TYPE (Query/Set device work type, transceiver mode or remote mode)

    There are no reviews for this product.

    Write a review

    Please login or register to review