Tags: Fingerprint, Scanner, Module, , reader, sensor, (R305), module, with, TTL, UART

Fingerprint Scanner Module

  • 149.00 AED
    • Ex Tax:149.00 AED
    • Product Code: FPM10
    • Availability: Out Of Stock
    This post is an introductory guide on how to use the Fingerprint Sensor Module with the Arduino. We’ll show you how to enroll a new fingerprint ID, and how to find a fingerprint match.Watch the Video DemonstrationIntroducing the Fingerprint Sensor ModuleFingerprint Sensor Module, like the one in the..

    • This post is an introductory guide on how to use the Fingerprint Sensor Module with the Arduino. We’ll show you how to enroll a new fingerprint ID, and how to find a fingerprint match.

      Watch the Video Demonstration

      Introducing the Fingerprint Sensor Module

      Fingerprint Sensor Module, like the one in the following figure, made fingerprint recognition more accessible and easy to add to your projects. This means that is is super easy to make fingerprint collection, registration, comparison and search.

      These modules come with FLASH memory to store the fingerprints and work with any microcontroller or system with TTL serial. These modules can be added to security systems, door locks, time attendance systems, and much more.


      • Voltage supply: DC 3.6 to 6.0V
      • Current supply: <120mA
      • Backlight color: green
      • Interface: UART
      • Bad rate: 9600
      • Safety level: five (from low to high: 1,2,3,4,5)
      • False Accept Rate (FAR): <0.001% (security level 3)
      • False Reject Rate (FRR): <1.0% (security level 3)
      • Able to store 127 different fingerprints

      Sensor Pinout

      The sensor has six pins that are labeled in the figure below.

      The fingerprint sensor module used in this project came with really thin wires, so soldering breadboard-friendly wires was needed. We recommend using different colors according to the pin function. In our case:

      • DNC – white wires
      • VCC – red wire
      • TX – blue wire
      • RX – green wire
      • GND – black wire

      The following table shows how to wire the sensor to the Arduino.

      Fingerprint SensorArduino
      VCC5V (it also works with 3.3V)
      TXRX (digital pin 2, software serial)
      RXTX (digital pin 3, software serial)

      Installing the Adafruit Fingerprint Sensor Library

      The easiest way to control the fingerprint sensor module with the Arduino is by using the Adafruit library for this sensor. Follow the next instructions to install the library:

      1. Click here to download the Adafruit Fingerprint Sensor library. You should have a .zip folder in your Downloads folder
      2. Unzip the .zip folder and you should get Adafruit-Fingerprint-Sensor-Library-master folder
      3. Rename your folder from  Adafruit-Fingerprint-Sensor-Library-master folder to  Adafruit_Fingerprint_Sensor_Library folder
      4. Move the folder to your Arduino IDE installation libraries folder
      5. Finally, re-open your Arduino IDE

      Enroll a New Fingerprint

      Having the fingerprint sensor module wired to the Arduino, follow the next steps to enroll a new fingerprint. Make sure you’ve installed the Adafruit Fingerprint Sensor library previously.

      1. In the Arduino IDE, go to File > Examples > Adafruit Fingerprint Sensor Library > Enroll.

      2. Upload the code, and open the serial monitor at a baud rate of 9600.

      3. You should enter an ID for the fingerprint. As this is your first fingerprint, type 1 at the top left corner, and then, click the Send button.

      4. Place your finger on the scanner and follow the instructions on the serial monitor.

      You’ll be asked to place the same finger twice on the scanner. If you get the “Prints matched!” message, as shown below, your fingerprint was successfully stored. If not, repeat the process, until you succeed.

      Store as many fingerprints you want using this method.

      Finding a Match

      You now should have several fingerprints saved on different IDs. To find a match with the fingerprint sensor, follow the next instructions.

      There are no reviews for this product.

      Write a review

      Please login or register to review


    *for faulty items and in-store drop off for unused items. T&C applies.

    Customer Support

    We really care about you and your order as much as you do. Please contact us without hesitation.


    We can ship your order internationally. Please contact us first before proceeding with your order.

    Fast Delivery

    You want your item next day? No problem! We advise contacting us ASAP to insure smooth delivery experience