Motor Drivers

Showing 1 to 33 of 33 (1 Pages)
Fan Module For Firefighter Flame Robot L9110

Fan Module For Firefighter Flame Robot L9110

33.00 AED

Ex Tax: 33.00 AED

This is a commonly found, basic low-cost module that consists of an L9110 chip and a small motor attached. you can use it to make a firefighter robot or any application needs a fan with speed controller, to control this module you need 4 connections between the Arduino and the module. VCC, GND, INA,..

IC Motor H-Bridge Driver chip 2ch 0.6A 25V L293D

IC Motor H-Bridge Driver chip 2ch 0.6A 25V L293D

5.00 AED

Ex Tax: 5.00 AED

Overview:The L293 and L293D devices are quadruple high-current half-H drivers. The L293 is designed to provide bidirectional drive currents of up to 1 A at voltages from 4.5 V to 25V. The L293D is designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 25 V. Both d..

IRF520 MOSFET Driver Module For Arduino/ARM/Raspbe...

IRF520 MOSFET Driver Module For Arduino/ARM/Raspbe...

19.00 AED

Ex Tax: 19.00 AED

When you need to control a device with a secondary power source from your low voltage micro-controller, you need something like this device. The basic principle is a small control voltage can provide and control higher voltage requirements of external devices like LED light strips, etc. via the MOSF..

Motor Drive Module High-power Smart Car Bts7960 43...

Motor Drive Module High-power Smart Car Bts7960 43...

81.00 AED

Ex Tax: 81.00 AED

The BTS 7960 is a fully integrated high current half, bridge for motor drive applications, comes with Two packages The Operating Voltage of 24V And Continuous current of 43A Max, PWM capability of up to 25 kHz combined with active freewheeling this IC Have a good protection  ..

Motor Driver Board Module L298n Dual H-Bridge DC S...

Motor Driver Board Module L298n Dual H-Bridge DC S...

34.00 AED

Ex Tax: 34.00 AED

L298 N Dual H-Bridge Stepper motor module driver for Arduino. It uses L298 N chip, can directly drive two 3V-30V DC motor, and provide a 5V support power source with the 5-volt regulator in it, you can drive the motor with  5V, 3.3V boards. the L289 single-chip driver made especially for M..

Motor Driver Module 2A 2- Motors L298N

RobotDYN

Motor Driver Module 2A 2- Motors L298N

35.00 AED

Ex Tax: 35.00 AED

Motor Driver L298N for Arduino with Logic control system allows to control of 2 DC-motors, to control rotational speed, rotational direction, to stop motors with freewheeling or to block their action. You can control each motor. Also, you may drive a bipolar step motor curre..

Motor Driver Module 2ch 0.6A 25V L293D

Motor Driver Module 2ch 0.6A 25V L293D

9.00 AED

Ex Tax: 9.00 AED

Overview:The L293 and L293D devices are quadruple high-current half-H drivers. The L293 is designed to provide bidirectional drive currents of up to 1 A at voltages from 4.5 V to 25V. The L293D is designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 25 V. Both d..

Motor Driver Module 2ch 0.8 12V HG7881- L9110S

Motor Driver Module 2ch 0.8 12V HG7881- L9110S

15.00 AED

Ex Tax: 15.00 AED

The HG7881 (L9110) is a compact motor driver board that supports a voltage range from 2.5-12V at 800mA of continuous current. These chips have built-in output clamp diodes to protect your sensitive microcontroller electronics. They are suitable for small robot projects.Each L9110 chip is able to dri..

Motor Driver Module 2ch 1.2A 15V TB6612FNG

Motor Driver Module 2ch 1.2A 15V TB6612FNG

15.00 AED

Ex Tax: 15.00 AED

The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the spe..

Motor Driver Module 2ch 2A 35V L298N

Motor Driver Module 2ch 2A 35V L298N

13.00 AED

Ex Tax: 13.00 AED

Using L298N as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, pleas..

Motor Driver Module 2ch mini 1.5A 10V MX1508

Motor Driver Module 2ch mini 1.5A 10V MX1508

19.00 AED

Ex Tax: 19.00 AED

This motor driver are using MX1508 ic to drive two channel motor. It's similar with L298N, can drive 2 motor with both CW & CCW direction, and control speed by PWM. 2 channel mini motor driver Voltage Input : 2-10VDC Rated Current: 1.5A Peak Current: 2.5A (less than 10second) Direction and PWM ..

Motor Driver Module L298p Pwm Speed Controller Dua...

Motor Driver Module L298p Pwm Speed Controller Dua...

68.00 AED

Ex Tax: 68.00 AED

L298P DC motor driver uses high-power motor driver chip L298P, can directly drive 2 straight Current motor, drive current up to 2 A, motor output uses 8 high-speed Schottky diodes as protection. The circuit wiring is reasonable and uniform With patch panels, the laminate design can be plugged direct..

Motor Driver Module Shield 1A L293B 2 Motors for A...

RobotDYN

Motor Driver Module Shield 1A L293B 2 Motors for A...

45.00 AED

Ex Tax: 45.00 AED

Motor Shield (1A) for Arduino allows you to control 2 DC motors: control the speed and direction of rotation, stop the motor or block movement. You can control each motor separately. You can also manage one bipolar stepper motor power up to 2A.Motor Shield (1A) is based on the ch..

Motor Driver Module Shield 2A 2-motors L298P

RobotDYN

Motor Driver Module Shield 2A 2-motors L298P

69.00 AED

Ex Tax: 69.00 AED

Motor Shield 2A for Arduino allows to control of 2 DC-motors, to control rotational speed, rotational direction, to stop motors with freewheeling or to block their action. You can control each motor. Also you may drive bipolar step motor current up to 4A.Motor Shield 2A for Arduino is based on L298P..

Motor Driver Module Shield 4ch 0.6A 25V L293D

Motor Driver Module Shield 4ch 0.6A 25V L293D

29.00 AED

Ex Tax: 29.00 AED

controlling 4 motors , or 2 DC Motors + Stepper motors or 2 stepper motors at once is not hard anymore adafruit Motor Shield is a great motor controller for Arduino, but you need to make sure it's used correctly. Please read and watch  the tutorial below.Features2 interface for 5V Ser..

Motor Driver Module Shield Board L293D For NodeMCU...

Motor Driver Module Shield Board L293D For NodeMCU...

25.00 AED

Ex Tax: 25.00 AED

Motor power supply (VM): 4.5V ~ 36V, can be powered separatelyControl power (VIN): 4.5V ~ 9V (10VMAX), can be powered separatelyModule provides short-circuit sub (short the VM and VIN), you can easily use one power (must 4.5V ~ 9V) while completing motor drive and controlLogic Operating current Iss:..

Motor Driver Module Shield DYN 4ch 0.6A 25V L293D

RobotDYN

Motor Driver Module Shield DYN 4ch 0.6A 25V L293D

39.00 AED

Ex Tax: 39.00 AED

The L293 Motor Shield is a great and quick way to control DC motors, servos or even stepper motors. It has the capability of controlling up to 2 stepper motors, 4 DC motors. and 2 servos. We think this shield would be a good start for beginners because of its versatility for its price range.Feature:..

Motor Driver PWM Speed Switching Controller DC 6V ...

Motor Driver PWM Speed Switching Controller DC 6V ...

21.00 AED

Ex Tax: 21.00 AED

This DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 0%-100%. The motor speed controller can easily provide a continuous current of3A to your DC motor or other DC load. Main technical pa..

Robot - Keyestudio Mini Tank Robot Ks0428

Keyestudio

Robot - Keyestudio Mini Tank Robot Ks0428

279.00 AED

Ex Tax: 279.00 AED

Ks0428 keyestudio Mini Tank Robot Upgraded V2IntroductionHere comes a keyestudio mini tank robot upgraded V2. This tank robot is essentially a two-drive tracked vehicle.The tank robot mainly uses the Control_Board, L298P driver shield and sensor shield V5, no soldering and e..

Romeo V2- an Arduino Robot Board (Arduino Leonardo...

Romeo V2- an Arduino Robot Board (Arduino Leonardo...

189.00 AED

Ex Tax: 189.00 AED

you need to control your robot ... without wires and connection that drive you crazy ?!this is all in one arduino based robot controller boared Romeo V2- an Arduino Robot Board (Arduino Leonardo) with Motor DriverRoMeo V2 is an All-in-One Arduino based robot board, it is especially designed for..

Servo Motor PWM Driver I2C Module 16-channel 12-bi...

Servo Motor PWM Driver I2C Module 16-channel 12-bi...

25.00 AED

Ex Tax: 25.00 AED

This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpersTerminal block for power input (or you can use the 0.1" breakouts on the side)Reverse polarity protection on the terminal block inputGreen power-good LED3 pin connectors in groups of 4 so you can plug in 16 servos at on..

Servo Motor PWM Driver I2C Module12-Bit Pwm Servo ...

Servo Motor PWM Driver I2C Module12-Bit Pwm Servo ...

19.00 AED

Ex Tax: 19.00 AED

You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you could j..

Servo Motor PWM Driver Shield Module16-channel 12-...

Servo Motor PWM Driver Shield Module16-channel 12-...

47.00 AED

Ex Tax: 47.00 AED

This shield is perfect if you want to build a robot, perhaps a hexapod or a project that requires several components that require movement. It is also ideal in controlling many LEDs with precise PWM signal and perform microprocessor has a limited number of PWM pin. For this applications, t..

Servo Tester With Indicator Light 4.8-6v Multi

Servo Tester With Indicator Light 4.8-6v Multi

16.00 AED

Ex Tax: 16.00 AED

Multi Servo Tester 4.8-6V with Indicator Light 3CH ECS Consistency Speed Controler Power CCPM Master Checker RC Drone Parts Features:1.The ability to easily detect and configure the server's virtual spaces, jitter and median.2.Can ..

Stepper Motor 12V With ULN2003 H Bridge Motor Cont...

Stepper Motor 12V With ULN2003 H Bridge Motor Cont...

19.00 AED

Ex Tax: 19.00 AED

The  12V Stepper Motor 28BYJ-48 :Voltage: 12VDiameter: 28mmReduction ratio: 1/64Step angle: 5.625 x 1 / 64Feature of the Driver:Stepper motor driver board with ULN2003.A, B, C, D four-phase LED indicates the status of the stepper motor work.Stepper motor with a standard interface, whe..

Stepper Motor 5V With ULN2003 H Bridge Motor Contr...

Stepper Motor 5V With ULN2003 H Bridge Motor Contr...

19.00 AED

Ex Tax: 19.00 AED

The Driver:The ULN2003 stepper motor driver board allows you to easily control the 28BYJ-48 stepper motor from a microcontroller, like the Arduino Uno. One side of the board side has a 5 wire socket where the cable from the stepper motor hooks up and 4 LEDs to indicate which coil is currently powere..

Stepper Motor Driver A3967 Easy Drive v4.3

Stepper Motor Driver A3967 Easy Drive v4.3

23.00 AED

Ex Tax: 23.00 AED

EasyDriver is a Stepper Motor Driver that can drive up to about 750mA per phase of a bipolar stepper motor. It defaults to 8 step microstepping mode. (So if your motor is 200 full steps per revolution, you would get 1600 steps/rev using EasyDriver.) This setting can be easily overridden by tying the..

Stepper Motor Driver A4988/drv8825 Reprap Red

Stepper Motor Driver A4988/drv8825 Reprap Red

12.00 AED

Ex Tax: 12.00 AED

3D Printer A4988 Reprap Step Motor Driver Module is a complete micro-stepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and ± 2 A. A4988 includes ..

Stepper Motor Driver Drv8825 A4988 42 Expansion Bo...

Stepper Motor Driver Drv8825 A4988 42 Expansion Bo...

25.00 AED

Ex Tax: 25.00 AED

On-board DIP switch, you can easily adjust the drive segments. Port: digit / Suitable for A4988, DVR8825. Terminal power connectors for easy connections drive power. Interface: Direction, enable, speed. Compatible with 12 / 24V drive scheme. Logic Voltage: 5V / Input voltage: 12-30V. Suitable for..

Stepper Motor Driver DRV8825 With Heat Sink

Stepper Motor Driver DRV8825 With Heat Sink

10.00 AED

Ex Tax: 10.00 AED

If you are planning on building your own 3D printer or a CNC machine, you will need to control a bunch of stepper motors. And having one Arduino control all of them can take up a lot of the processing and not leave you a lot of room to do anything else; unless you use a self-contained dedicated step..

Stepper Motor Driver Hy-div268n-5a Subdivision Typ...

Stepper Motor Driver Hy-div268n-5a Subdivision Typ...

149.00 AED

Ex Tax: 149.00 AED

Two-phase hybrid stepping motor dynamic voltage 12 to 48V, the current is less than 5A outer diameter of 35 to 86 mm. This drive using the drive's current loop subdivision control, the motor torque ripple is very small, low-speed running is very smooth, almost no vibration and noise. High-speed torq..

Stepper Motor Driver Tb6560 3A Single Axis Control...

Stepper Motor Driver Tb6560 3A Single Axis Control...

79.00 AED

Ex Tax: 79.00 AED

The TB6560 Driver Board 3A CNC Router Single 1 Axis ControllerStepper Motor driver board is for axis control with Input signal high-speed optocoupler isolation, the large heat sink to ensure good heat dissipation. Stepper motor driver is Semi-flow mode adjustable, semi-flow current ad..

Stepper Motor Driver ULN2003 For Arduino Microcont...

Stepper Motor Driver ULN2003 For Arduino Microcont...

5.00 AED

Ex Tax: 5.00 AED

The ULN2003 Stepper Motor Driver Board allows you to easily control the 28BYJ-48 Stepper motor or Dc Motor from a microcontroller, like the Arduino/AVR/PIC. One side of the board has a 5 wire socket where the cable from the stepper motor hooks up and it has 4 LED to indicate which coil is currently ..

Showing 1 to 33 of 33 (1 Pages)