Motor Drivers

Showing 1 to 13 of 13 (1 Pages)
IRF520 MOS Driver Module For Arduino/ARM/Raspberry...

techmaze

IRF520 MOS Driver Module For Arduino/ARM/Raspberry...

19.00 AED

Ex Tax: 19.00 AED

When you need to control a device with a secondary power source from your low voltage micro-controller, you need something like this device. The basic principal is a small control voltage can provide and control higher voltage requirements of external devices like LED light strips, etc. via the MOSF..

Motor Driver Module 2Ch 0.6A 25V L293D

China

Motor Driver Module 2Ch 0.6A 25V L293D

10.00 AED

Ex Tax: 10.00 AED

Overview:The L293 and L293D devices are quadruple high-current half-H drivers. The L293 is designed to provide bidirectional drive currents of up to 1 A at voltages from 4.5 V to 25V. The L293D is designed to provide bidirectional drive currents of up to 600-mA at voltages from 4.5 V to 25 V. Both d..

Motor Driver Module 2Ch 0.8 12V HG7881

Motor Driver Module 2Ch 0.8 12V HG7881

15.00 AED

Ex Tax: 15.00 AED

The HG7881 (L9110) is a compact motor driver board that supports a voltage range from 2.5-12V at 800mA of continuous current. These chips have built-in output clamp diodes to protect your sensitive microcontroller electronics. They are suitable for small robot projects.Each L9110 chip is able to dri..

Motor Driver Module 2Ch 1.2A 15V TB6612FNG

China

Motor Driver Module 2Ch 1.2A 15V TB6612FNG

12.00 AED

Ex Tax: 12.00 AED

The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the spe..

Motor Driver Module 2Ch 2A 35V L298N
sale-32%

Keyestudio

Motor Driver Module 2Ch 2A 35V L298N

13.00 AED

19.00 AED

Ex Tax: 13.00 AED

Using L298N as the control chip,the module has such characteristics as strong driving ability,low calorific value and strong anti-interference ability. This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage of the voltage stabilizing chip, pleas..

Motor Driver Module 2Ch mini 1.5A 10V L298N

China

Motor Driver Module 2Ch mini 1.5A 10V L298N

18.00 AED

Ex Tax: 18.00 AED

1.Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motors2.Built-in TSD, without worrying about motor stall3.Ultra-small size, suitable for assembly and carSpecification:1.Module supply voltage: DC 2V-10V2.Signal input voltage: DC 1.8-7V3.Single working current: 1.5A..

Motor Driver Module 4Ch 0.6A 25V L293D
sale-36%

Motor Driver Module 4Ch 0.6A 25V L293D

29.00 AED

45.00 AED

Ex Tax: 29.00 AED

controlling 4 motors , or 2 DC Motors + Stepper motors or 2 stepper motors at once is not hard anymore adafruit Motor Shield is a great motor controller for Arduino, but you need to make sure it's used correctly. Please read and watch  the tutorial below.Features2 interface for 5V Ser..

Motor Driver Shield Board L293D For NodeMCU V2

China

Motor Driver Shield Board L293D For NodeMCU V2

22.00 AED

Ex Tax: 22.00 AED

Motor power supply (VM): 4.5V ~ 36V, can be powered separatelyControl power (VIN): 4.5V ~ 9V (10VMAX), can be powered separatelyModule provides short-circuit sub (short the VM and VIN), you can easily use one power (must 4.5V ~ 9V) while completing motor drive and controlLogic Operating current Iss:..

Romeo V2- an Arduino Robot Board (Arduino Leonardo...

Romeo V2- an Arduino Robot Board (Arduino Leonardo...

192.50 AED

Ex Tax: 192.50 AED

you need to control your robot ... without wires and connection that drive you crazy ?!this is all in one arduino based robot controller boared Romeo V2- an Arduino Robot Board (Arduino Leonardo) with Motor DriverRoMeo V2 is an All-in-One Arduino based robot board, it is especially designed for..

Servo Motor PWM Driver I2C Module 16-Channel 12-bi...

China

Servo Motor PWM Driver I2C Module 16-Channel 12-bi...

25.00 AED

Ex Tax: 25.00 AED

This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpersTerminal block for power input (or you can use the 0.1" breakouts on the side)Reverse polarity protection on the terminal block inputGreen power-good LED3 pin connectors in groups of 4 so you can plug in 16 servos at on..

Stepper Motor Driver DRV8825 With Heat Sink

China

Stepper Motor Driver DRV8825 With Heat Sink

10.00 AED

Ex Tax: 10.00 AED

If you are planning on building your own 3D printer or a CNC machine, you will need to control a bunch of stepper motors. And having one Arduino control all of them can take up a lot of the processing and not leave you a lot of room to do anything else; unless you use a self-contained dedicated step..

Stepper Motor Driver ULN2003 For Arduino Microcont...
sale-44%

techmaze

Stepper Motor Driver ULN2003 For Arduino Microcont...

5.00 AED

9.00 AED

Ex Tax: 5.00 AED

The ULN2003 Stepper Motor Driver Board allows you to easily control the 28BYJ-48 Stepper motor or Dc Motor from a microcontroller, like the Arduino/AVR/PIC. One side of the board has a 5 wire socket where the cable from the stepper motor hooks up and it has 4 LED to indicate which coil is currently ..

Stepper Motor with ULN2003 H Bridge Motor Controll...
sale-24%

Stepper Motor with ULN2003 H Bridge Motor Controll...

19.00 AED

25.00 AED

Ex Tax: 19.00 AED

The ULN2003 stepper motor driver board allows you to easily control the 28BYJ-48 stepper motor from a microcontroller, like the Arduino Uno. One side of the board side has a 5 wire socket where the cable from the stepper motor hooks up and 4 LEDs to indicate which coil is currently powered. The moto..

Showing 1 to 13 of 13 (1 Pages)